USER MANUAL LED MOVING HEAD
←
→
Transcription du contenu de la page
Si votre navigateur ne rend pas la page correctement, lisez s'il vous plaît le contenu de la page ci-dessous
LED MOVING HEAD
USER MANUAL
Keep this manual for future needs
V 1.0 07.2011
ENGLISH FRANÇAIS2 USER MANUAL
Summary Sommaire
4 Introduction 22 Introduction
4 Description of the device 22 Description du projecteur
4 Overview 22 Vue d’ensemble
5 Safety instructions 23 Instructions de sécurité
5 General guidelines 23 Instructions générales
6 Installation instructions 24 Instructions d’installation
6 Installation method via clamp 24 Méthode d’installation avec des crochets
7 DMX-512 control connection 25 Connexion DMX 512
7 DMX-512 connection with DMX terminator 25 Connexion DMX 512 avec bouchon de terminaison
7 Led Moving Head DMX starting adress selection 25 Réglage de l’adresse DMX du projecteur
7 Operating instructions of the internal 25 Réglage du système interne wireless DMX
DMX wireless system DMX sans fil)
8 Control Board 26 Panneau de contrôle
9 Function mode 27 Function mode
10 Information 28 Information
11 Personality 29 Personality
13 Reset-functions 31 Reset-functions
13 Effect Adjust 32 Effect Adjust
14 Users mode set 32 Users mode set
14 Edit program 32 Edit program
16 Instruction on use 33 Charte DMX du WILDSUN 500
18 Error message 36 Entretien et maintenance
18 PAN - movement Er 36 Nettoyage
18 TILT - Movement Er 36 Surveillance
18 Cleaning and maintenance 36 Spécifications techniques
18 Technical specifications 36 Optique
18 Optics 36 Source
18 Source 36 Mouvement
18 Movement 36 Couleurs
18 Colours 36 Dimmer, strobe
18 Dimmer, strobe 36 Contrôle
19 Control 37 Caractéristiques logicielles
19 Software facilities 37 Caractéristiques matérielles
19 Hardware facilities 37 Alimentation
19 Power supply 37 Refroidissement
19 Cooling system 37 Construction
19 Housing 37 Fixation
19 Rigging 37 Paramètres d’utilisation
19 Operating parameters 37 Conformité
19 Conformity 37 Dimensions
19 Size 37 Poids
19 Weight 38 Mousse pour réalisation d’un «flightcase»
20 Flightcase foam 38 Garantie
20 Warranty
USER MANUAL 3Thank you for your patronage. We are confident that our for address setting or access other functions setting.
ENGLISH |
excellent products and service can satisfy you. For your own Wireless receiver pre-installed
safety, please read this user manual carefully before installing Software-upload by optional accessory via DMX line
the device. Preset program: 7 built in programs can be called up via
In order to install, operate, and maintain the lighting safety DMX controller
INTRODUCTION | DESCRIPTION OF THE DEVICE | OVERVIEW
and correctly. We suggest that the installation and operation
should be done by the verified technician and follow the
instruction strictly.
Overview
CAUTION !
Unplug mains lead before opening the housing.
1
Every person involved with the installation, operation and
maintenance of this device has to:
be qualified
follow carefully the instructions of this manual
Introduction
9
Thank you for having chosen this professional LED Moving
Head projector. 10
You will see you have acquired a powerful and versatile 11
device.
12
Unpack the device. Inside the box you should find :
1. One XLR connection cable
2 3 4 5 6 7 8
2. Two omega clamps
3. One safety rope
4. Manual
Please check carefully that there is no damage caused by
transportation. Should there be any, consult your dealer and
don’t install this device.
Description of the device
31 x 13W high power four-colors LEDs (Red / Green /
Blue / White)
3 DMX Channel modes: 17, 24, 49 DMX channels
selectable for numerous applications
Pan movement: pan 540°/630°, Tilt movement: tilt 265°
Strobe-effect with 1 to 25 flashes per second
Zoom: 11° to 45° linear zoom
General dimming and blackout for all four effect
Excellent RGBW mixing and rainbow effect
Control board with full color LCD graphic display and
touch-keyboard
13 14 15 16 17 18 19 20
Rechargeable back-up Battery for Display, no need
external power supply, enable users to enter display menu
4 USER MANUAL1. Lens 11. ENTER-button in use or before cleaning it. Only handle the power cord by
| ENGLISH
2. Display 12. Handle the plug. Never pull out the plug by tugging the power cord.
3. Wireless indicator 13. Antenna - Wireless DMX
4. DSP Switch 14. 5-Pin DMX in Fixtures cannot be installed on combustible substances,
5. Microphone 15. 5-Pin DMX out keep more than 50cm distance with wall for smooth air flow,
SAFETY INSTRUCTIONS | GENERAL GUIDELINES
6. LEFT-button 16. 3-Pin DMX in so there should be no shelter for fans and ventilation for heat
7. DOWN-button 17. 3-Pin DMX out radiation.
8. RIGHT-button 18. Power Switch
CAUTION !
9. MODE/ESC-button 19. Fuse
10. UP-button 20. Power input
PROJECTOR USING CLASS 2 LED SOURCES
(EN60625-1 : 1994)
This device uses multiple high-power (CLASS 2) LED
Safety instructions (Light Emitting Diode) light sources.
CAUTION ! Never look directly at the light source when it is lit; never
Be careful with your operations. With a stand directly in the device’s beam close up.
dangerous voltage you can suffer a dangerous Always ensure the power is disconnected when installing,
electric shock when touching wires. dismantling or replacing the device to prevent any risk of glare
and to avoid any harm to your eyes.
This device has left the factory in perfect condition. In order
to maintain this condition and to ensure a safe operation,
it is absolutely necessary for the user to follow the safety
CAUTION !
Never touch the device during operation !
instructions and warning notes written in this user manual.
The housing may heat up.
Important :
Damages caused by the disregard of this user manual are
not subject to warranty. The dealer will not accept liability CAUTION !
for any resulting defects or problems. Never look directly into the light source, as
sensitive persons may suffer an epileptic shock.
If the device has been exposed to temperature changes due
to environmental changes, do not switch it on immediately. Please be aware that damages caused by manual
The arising condensation could damage the device. Leave modifications to the device are not subject to warranty. Keep
the device switched off until it has reached room temperature. away from children and non-professionals.
This device falls under protection-class I. Therefore it is
essential that the device should be earthed. General guidelines
The electric connection must carry out by qualified person. This device is a lighting effect for professional use on stages,
in discotheques, theatres, etc., the device was designed for
No move at operating mode. indoor use only.
If the external flexible cable or cord of this luminaire is This fixture is only allowed to be operated with the max
damaged, it shall be exclusively replaced by the manufacturer alternating current which stated in the technical specifications
or his service agent or a similar qualified person in order to of this manual.
avoid a hazard.
Lighting effects are not designed for permanent operation.
Make sure that the available voltage is not higher than stated Consistent operation breaks may ensure that the device will
at the end of this manual. serve you for a long time without defects.
Make sure the power cord is never crimped or damaged by
sharp edges. If this would be the case, replacement of the Do not shake the device. Avoid brute force when installing or
cable must be done by an authorized dealer. operating the device.
Always disconnect from the mains, when the device is not While choosing the installation-spot, please make sure that
USER MANUAL 5the device is not exposed to extreme heat, moisture or dust.
ENGLISH |
Please don’t project the beam onto combustible substances. CAUTION !
The minimum distance between light-output from the Led Before taking into operation for the first time, the
Moving Head and the illuminated surface must be more than installation has to be approved by an expert.
0.5 meter.
GENERAL GUIDELINES | INSTALLATION INSTRUCTIONS
Cautions :
If you use the quick lock cam in hanging up the fixture, please The effect should be installed outside areas where persons
make sure the quick lock fasteners turned in the quick lock may reach it, walk by or be seated.
holes correctly.
Overhead mounting requires extensive experience, including
Operate the device only after having familiarized with its amongst others calculating working load limits, installation
functions. Do not permit operation by persons not qualified material being used, and periodic safety inspection of
for operating the device. Most damages are the result of all installation material and the device. If you lack these
unprofessional operation. qualifications, do not attempt the installation yourself.
Improper installation can result in bodily injury.
Please use the original packaging if the device is to be
transported.
CAUTION !
The electric connection must only be carried
For safety reasons, please be aware that all modifications on
out by a qualified electrician.
the device are forbidden.
If this device will be operated in any way different to the one
Before mounting make sure that the installation area can hold
described in this manual, the product may suffer damages
a minimum point load of 10 times the device’s weight.
and the guarantee becomes void. Furthermore, any other
Connect the fixture to the mains with the power plug.
operation may lead to short-circuit, burns, electric shock,
lamp explosion, crash, etc.
Installation method via clamp
Installation instructions Please refer to the picture below:
CAUTION !
Please consider the GB7000.15/EN60598-2-17
and the other respective national norms during
the installation. The installation must only be
carried out by a qualified person.
The applicable temperature for the Led Moving Head is
between 0°C to 40°C. Do not use the Led Moving Head
under or above the temperature.
The installation of the effect has to be built and constructed in
a way that it can hold 10 times the weight for 1 hour without
any harming deformation.
The installation must always be secured with a secondary
safety attachment, e.g. an appropriate safety rope.
Never stand directly below the device when mounting,
removing or servicing the fixture. Fix the clamp on the bracket by tighten up the M12 screw
The operator has to make sure the safety relating and on the bracket to the M13 hole in the middle of the bracket.
machine technical installations are approved by an expert Insert the quick-lock fasteners of the first Omega holder into
before taking the device into operation for the first time. the respective holes on the bottom of the device. Tighten the
These installations have to be approved by a skilled person quick-lock fasteners fully clockwise.
once a year. Install the second Omega holder.
Pull the safety-rope through the holes on the bottom of the
base and over the trussing system or a safe fixation spot.
6 USER MANUALInsert the end in the carabiner and tighten the safety screw. the correct number on the display located on the base of the
| ENGLISH
device.
DMX-512 control connection
You can set the same starting address for all fixtures or a
group of fixtures, or make different address for each fixture
INSTALLATION INSTRUCTIONS
Connect the provided XLR cable to the female 3-pin or5-pin
XLR output of your controller and the other side to the male individually.
3-pin or5-pin XLR input of the moving head. You can chain If you set the same address, all the units will start to “listen”
multiple Moving Head together through serial linking. The to the same control signal from the same channel number. In
cable needed should be two core, screened cable with XLR other words, changing the settings of one channel will affect
input and output connectors. Please refer to the following all the fixtures simultaneously.
diagram. If you set a different address, each unit will start to “listen”
DMX Output DMX Input DMX Output DMX Input
to the channel number you have set, based on the quantity
of control channels of the unit. That means changing the
3-Pin XLR Socket 3-Pin XLR Socket 5-Pin XLR Socket 5-Pin XLR Socket
1. Ground
5 1 1 5
2
3
1 1
3
2 1. Ground
2. Data (-) 4
3
2 2
3
4
2. Data (-)
3. Data (+) settings of one channel will affect only the selected fixture.
3. Data (+) 4. Open
5. Open
In the case of the Moving head, which is a 24 channel fixture,
you should set the starting address of the first unit to 1, the
second unit to 25 (24 + 1), the third unit to 49 (24+ 25), and
so on.
Operating instructions of the internal
DMX wireless system
Address 1 Address 25 Address 49
1. Equipments:
DMX 512 controller, wireless transmitter, and the fixtures with
DMX-512 connection with DMX wireless receiver.
terminator
2. Message from the LED indicator:
For installations where the DMX cable has to run a long 1) Rapid flashing red/Green: logging in to a transmitter
distance or is in an electrically noisy environment, such as in 2) Slow flashing Red/Green: Logged on a transmitter and
a discotheque, it is recommended to use a DMX terminator. the DMX line is idle (No DMX is connected to transmitter).
This helps in preventing corruption of the digital control signal 3) Solid Green: Logged on to a transmitter and receiving
by electrical noise. The DMX terminator is simply an XLR plug DMX data.
with a 120 Ohms resistor connected between pins 2 and 3, 4) Solid Red: Not logged on to a transmitter (free)
which is then plugged into the output XLR socket of the last
fixture in the chain. Please see illustrations below. 3. WDMX in the menu of the fixture:
On a fixture installed with wireless system, in order to switch
between wireless control system and traditional DMX control
(with cable), a new menu WDMX is added to the display
board.
ON: (Activate WDMX)
1 When the fixture is power ON, and the WDMX is activated
to ON status, but did not connect to the controller and did
not log in to the transmitter, the fixture will search for the
DMX signal source. If the fixture is connected to the DMX
Led Moving Head DMX starting controller it can be controlled by DMX controller; if it is log
address selection in to the wireless transmitter, it can be controlled by the
Transmitter.
All fixtures should be given a DMX starting address when When the fixture is power OFF, and the WDMX is in ON
using a DMX signal, so that the correct fixture responds to status, if the fixture is connected to DMX controller. After
the correct control signals. This digital starting address is the the fixture is power on, it can be controlled only by the
channel number from which the fixture starts to “listen” to the DMX controller which connected. The fixture can log in
digital control information sent out from the DMX controller. the wireless transmitter, and receive only radio signal from
The allocation of this starting address is achieved by setting transmitter, but not DMX from the transmitter.
USER MANUAL 7OFF: (De-activate WDMX) Control Board
ENGLISH |
In this status, wireless system is not activated, so the
fixture can not log in the transmitter. The Control Board offers several features: you can simply set
REST: (reset WDMX memory) the starting address , run the pre-programmed program or
Can remove the fixture from the connection with the
INSTALLATION INSTRUCTIONS
make a reset.
transmitter, the fixture become free and ready to log in
any transmitter. The main menu is accessed by pressing the button until
the display starts flashing.
4. Setup the wireless system: Browse through the menu by pressing the button,
a) Connect the transmitter with the DMX controller button, button or button. Press the Enter-
b) To make the fixture installed with wireless receiver log in to button in order to select the desired menu. You can change
the transmitter the selection by pressing the the button, button,
Initially, the indicator on the receiver fixture should be in button or button.
Solid red Confirm every selection by pressing the button. You can
Press and hold the configuration button on transmitter for leave every mode by pressing the button. The functions
less than 3 seconds the red/green LEDs on the transmitter provided are described in the following sections. it will exit
and the receiver fixture will flash rapidly for about 5 ~ from flash 10 seconds after the last keypress. Press this key
10 seconds while the system goes through its setup under edit mode. The functions provided are described in the
procedure. following sections.
Once the receiver fixture is logged in to the transmitter
(T1), the fixture with wireless receiver will keep the memory, To access the display menu via the internal battery, press
even if restart the power, this unit will log in the transmitter the DSP button for 2 seconds; To shut off the display
(T1) automatically. immediately, choose the commend « Reset All» menu
c) Use the DMX 512 to control the fixture and press «Enter» button, otherwise, the display will
automatically switch off about 1 minute from last button
5. Remove the receivers from transmitter (T1) and to log in press.
to another transmitter (T2)
Case 1: Remove a receiver:
On the control board of the fixture, enter menu to activated
the function of REST;
The LED for wireless on the fixture should turn to Solid
red; the receiver can log out from the transmitter (T1);
Press the configuration button on transmitter(T2) for less
than 3 second, then the fixture will start to connect with
the transmitter (T2)
Case 2: Remove all receivers from a transmitter (T1) to log
in to T2;
Press and hold the configuration button on the T1 as least
5 seconds, can clear the connection with all the fixtures.
All the red/green LEDs on the receiver fixtures will turn to
Solid red to indicate that the receivers are unassigned and
removed from the transmitter ( T1);
Press and hold the configuration button on the T2 less
then less than 3 second, the fixtures will connect with the
T2
PS:
1. Please log the receivers out from the transmitter after every
job, so that the receivers are in free un assigned state and
ready to be assigned to a transmitter.
2. Do not connect the fixture which is under the communication
of wireless system to the DMX controller, otherwise it will
cause interference from the DMX controller.
8 USER MANUALFunction Mode
Set Dmx Address A001~AXXX DMX address setting Value Display
| ENGLISH
Value Display PAN… DMX value display
Set To Slave Slave1,Slave2,Slave3 Slave setting With this function you can display the DMX 512 value of each
Auto Program Master / Alone Auto program
Music Control Master / Alone Music control channel. The display automatically shows the channel with a
Time Information Current Time XXXX(Hours) Power on running time value changing.
Total Life Hours XXXX(Hours) Fixture running time
1. Access the main menu.
INSTALLATION INSTRUCTIONS
Last Run Hours XXXX(Hours) Fixture Last times clear
Information
Timer Password Password=XXX Timer Password 038
Clear Last Run ON/OFF Clear Fixture Last time 2. Tap the button until “Value Display” is
Temperature Info Head Temperature XXX °C / °F Temperature in the head displayed.
Software Version Ver 1.0 Software version of each IC 3. Press ENTER, the display will show “Value Display”.
Status Settings Address via DMX ON/OFF Add. via DMX
No DMX Status Close/Hold/Auto/Music Auto run if no DMX 4. Tap the button, choose each channel.
Pan Reverse ON/OFF Pan Reverse movement
Tilt Reverse ON/OFF Tilt Reverse movement
5. Press ENTER to confirm or press to
Pan Degree 630/540 Pan Degree Select return to the main menu.
Feedback ON/OFF Movement Feedback switch
Movement Speed Speed 1~ 4 Movement Mode Select
Zoom Speed Speed 1~ 2 Zoom Mode Select
Mic Sensitivity 0~99% Sensitivity of Mic. Set to slave
Hibernation OFF/1~99M 15M Standby mode
Fans Control Head Control Auto Fans Speed Head Fans Speed Mode
With this function, you can define the device as slave.
High Fans Speed Select 1. Access the main menu.
Low Fans Speed
2. Tap the button until “Set To Slave” is
Personality
Base Control 10% Base Fans Speed Mode
30%
50%
Select
displayed.
Display Setting Shutoff Time 02~60m 05m 3. Press ENTER, the display will show “Set To Slave”.
Display Reverse ON/OFF
Key Lock ON/OFF
4. Tap the button, the display will show
Temperature C/F Celsius Temperature switch between “Slave1”, ”Slave2”, ”Slave3”.
Fahrenheit °C / °F
Initial Effect PAN PAN =XXX Initial effect position
5. Press ENTER to confirm or press to
Wireless DMX De-Act WDMX De-activate WDMX return to the main menu.
Activate WDMX Activate WDMX
Act & Data Out Act & Data Out
Rest WDMX Mem Reset Wireless DMX Mem
Auto Program
Reset Default ON/OFF Restore factory sett.
Reset All Reset all motors
With this function, you can run the internal program. You can
Function
Reset
Reset Pan&Tilt Reset Pan&Tilt select the desired program under “Select program”. You can
Reset Zoom Reset Zoom
Test Channel PAN Test function set the number of steps under “Edit program”. You can edit
Effect Adjust
Manual Control PAN PAN =XXX Control the light the individual scenes under “Edit scenes”. With this function,
Calibrate Values --Password--
PAN
Password=XXX
PAN=XXX
Calibrate and adjust the
effects to standard/right
you can run the individual scenes either automatically, i.e.
: : position Password “050” with the adjusted Step-Time.
User Mode Standard Mode User’s mode to change
Basic Mode channel numbers 1. Access the main menu.
Users Mode Set
Extended Mode
User Mode A
2. Tap the button until “Auto Program” is
User Mode B displayed.
User Mode C
Edit User Mode PAN PAN = CH01 Preset User modes
3. Press ENTER, the display will show “Auto Program”.
Select Programs Auto Pro Part 1 Program 1 ~ 10 Program 1 Select programs to be run 4. Tap the button, the display will show
Auto Pro Part 2 Program 1 ~ 10 Program 2
Auto Pro Part 3 Program 1 ~ 10 Program 3 “Master1”, ” Alone”.
Edit Program Program 1 Program Test (“STEP XX”) Testing program
5. Press ENTER to confirm or press to
Edit Program
: Step 01=SCxxx Program in loop
Program 10 Step 64=SCxxx Save and exit return to the main menu.
Edit Scenes Edit Scene 001 Pan,Tilt,…… Pan=xxx…… Save and automatically return
~ Edit Scene --Secne Time-- TIME=xx.xs manual scenes edit
Rec. Controller
250
XX~XX
Input By Outside
Automat. scenes rec
Music control
With this function, you can run the internal program sound-
controlled.
Function mode 1. Access the main menu.
2. Tap the button until “Music control” is
Set DMX Address displayed.
With this function, you can adjust the desired DMX-address
3. Press , the display will show “Music control”.
via the Control Board.
4. Tap the button, the display will show
1. Access the main menu.
“Master1”, ” Alone”.
2. Tap the button until “Set DMX Address” is
5. Press to confirm or press to
displayed.
return to the main menu.
3. Press ENTER, the display will show “Set DMX Address”.
4. Tap the button, the display will show
“A001~AXXX”
5. Press ENTER to confirm or press to
return to the main menu.
USER MANUAL 9Information Timer Password
ENGLISH |
With this function, you can display the timer password.
Time information 1. Tap button, access the main menu, Tap
the button until “Information” is displayed.
Press ENTER, the display will show “Information”. Tap
INSTALLATION INSTRUCTIONS
Current Time
With this function, you can display the temporary running the button until the display will show “Timer
time of the device from the last power on. The display shows Password”. Press ENTER, the display will show “Timer
“XXXX”, “XXXX” stands for the number of hours. The counter Password”.
is resetted after turning the device off. 2. Press , the display will show “Timer
1. Tap button, access the main menu, Tap Password”.
the button until “Information” is displayed. 3. Press < ENTER>, the display will show “Timer Password”.
Press ENTER, the display will show “Information”. Tap The time password is 038.
the button until the display will show “Timer 4. Press to confirm or press to
Password”. Press ENTER, the display will show “Timer return to the main menu.
Password”.
2. Press , the display will show “Current Time”. Clear Last Run
3. Press , the display will show “Current Time”. With this function, you can clear last run time of the fixture.
4. The display will show “XXXX” (Hours); The display shows “ON” or “OFF”, Press “Enter” to confirm.
5. Press to confirm or press to 1. Tap button, access the main menu, Tap
return to the main menu. the button until “Information” is displayed.
Press ENTER, the display will show “Information”. Tap
Total Life Hours the button until the display will show “Timer
With this function, you can display the running time of the Password”. Press ENTER, the display will show “Timer
device. The display shows “XXXX”, “XXXX” stands for the Password”.
number of hours. 2. Press , the display will show “Clear Last
1. Tap button, access the main menu, Tap Run”.
the button until “Information” is displayed. 3. At “L-Timer Password” menu input right password, Press
Press ENTER, the display will show “Information”. Tap < ENTER>, the display will show “Clear Last Run”.
the button until the display will show “Timer 4. The display show “OFF”,Press , the display
Password”. Press ENTER, the display will show “Timer will show “ON”.
Password”. 5. Press to confirm or press to
2. Press , the display will show “Total Life return to the main menu.
Hours”.
3. Press< ENTER>, the display will show “Total Life Hours”. Temperature Info
4. The display will show “XXXX” (Hours);
5. Press to confirm or press to Head Temperature
return to the main menu. With this function you can display the current temperature of
the head of the fixture.
Last Run Hours 1. Tap button, access the main menu, Tap
With this function, you can display the last running time of the the button until “Information” is displayed.
fixture since the last reset. The display shows “XXXX”, “XXXX” Press ENTER, the display will show “Information”. Tap the
stands for the number of hours. button until “Temperature Info” is displayed.
1. Tap button, access the main menu, Tap Press ENTER, the display will show “Temperature Info”.
the button until “Information” is displayed. 2. Press , the display will show “Head
Press ENTER, the display will show “Information”. Tap Temperature”.
the button until the display will show “Timer 3. Press , the display will show “Head
Password”. Press ENTER, the display will show “Timer Temperature”.
Password”. 4. The display show “XXX °C / °F”.
2. Press , the display will show “Last Run 5. Press to confirm or press to
Hours”. return to the main menu.
3. Press < ENTER>, the display will show “Last Run Hours”.
4. The display will show “XXXX” (Hours); Software version
5. Press to confirm or press to With this function, you can display the software version of
return to the main menu. the device.
10 USER MANUAL1. Tap button, access the main menu, Tap setting”. Press , the display will show “Status
| ENGLISH
the button until “Information” is displayed. setting”.
Press ENTER, the display will show “Information”. 2. Press , the display will show “Pan Reverse”.
2. Press , the display will show “Software 3. Press , the display will show “Pan Reverse”.
version”. 4. The display show “OFF”, Press , the display
INSTALLATION INSTRUCTIONS
3. Press , the display will show “Software version”. will show “ON”.
4. The display show “Ver 1.0……”. 5. Press to confirm or press to
5. Press to confirm or press to return to the main menu.
return to the main menu.
Tilt Reverse
Personality With this function you can reverse the Tilt-movement.
1. Tap button, access the main menu, Tap
Status setting the button until “Personality” is displayed.
Press ENTER, the display will show “Personality”. Tap
Address via DMX the button until the display will show “Status
With this function, you can adjust the desired DMX-address setting”. Press , the display will show “Status
via an external controller. setting”.
1. Tap button, access the main menu, Tap 2. Press , the display will show “Tilt Reverse”.
the button until “Personality” is displayed. 3. Press , the display will show “Tilt Reverse”.
Press ENTER, the display will show “Personality”. Tap the 4. The display show “OFF”, Press , the display
button until the display will show “Status will show “ON”.
setting”. Press ENTER, the display will show “Status 5. Press to confirm or press to
setting”. return to the main menu.
2. Press , the display will show “Address via
DMX”. Pan Degree
3. Press , the display will show “Address via With this function, you can select pan degree for 630 or 540.
DMX”. 1. Tap button, access the main menu, Tap
4. The display show “ON”, Press , the display the button until “Personality” is displayed.
will show “OFF”. Press ENTER, the display will show “Personality”. Tap the
5. Press to confirm or press to button until the display will show “Status
return to the main menu. setting”. Press ENTER, the display will show “Status
setting”.
No DMX Status 2. Press , the display will show “Pan Degree”.
With this function, when the drive is not DMX signal, it runs 3. Press , the display will show “Pan Degree”.
automatism, close, hold and music, the default is hold. 4. The display show “540”, Press , the display
1. Tap button, access the main menu, Tap will show “630”.
theMovement Speed ENTER, the display will show “Personality”. Tap the button until the display will show “Status setting”.
1. Tap button, access the main menu, Tap Press ENTER, the display will show “Status setting”.
the button until “Personality” is displayed. 2. Press , the display will show “Hibernation”.
Press ENTER, the display will show “Personality”. Tap the 3. Press , the display will show “Hibernation”.
INSTALLATION INSTRUCTIONS
button until the display will show “Status 4. The display show “15M”, Press , the display
setting”. Press ENTER, the display will show “Status will show “01M”, “02M” …. “99M” or“OFF”.
setting”. 5. Press to confirm or press to
2. Press , the display will show “Movement return to the main menu.
Speed”.
3. Press , the display will show “Movement Fans Control
Speed”.
4. The display show “Speed 1”, Press , the Head Control
display will show “Speed 2”, “Speed 3”, “Speed 4”. With this function, you can set the speed of the running head
5. Press to confirm or press to fans. The selections have Auto, high and low.
return to the main menu. 1. Tap button, access the main menu, Tap
the button until “Personality” is displayed. Press
Zoom Speed ENTER, the display will show “Personality”. Tap the button until the display will show “Fans Control”.
“Speed 1” and “Speed 2”. “Speed 2” is the faster setting. Press ENTER, the display will show “Fans Control”.
1. Tap button, access the main menu, Tap 2. Press , the display will show “Head Control”.
the button until “Personality” is displayed. 3. Press , the display will show “Head Control”.
Press ENTER, the display will show “Personality”. Tap the 4. The display show “Auto Fans Speed”, Press , the display will show “High Fans Speed”, “Low
setting”. Press ENTER, the display will show “Status Fans Speed”.
setting”. 5. Press to confirm or press to
2. Press , the display will show “Zoom Speed”. return to the main menu.
3. Press , the display will show “Zoom Speed”.
4. The display show “Speed 1”, Press , the Base Control
display will show “Speed 2”. With this function, you can set the speed of the running base
5. Press to confirm or press to fans. The selections have 10%, 30% and 50%.
return to the main menu. 1. Tap button, access the main menu, Tap
the button until “Personality” is displayed. Press
Mic Sensitivity ENTER, the display will show “Personality”. Tap the button until the display will show “Fans Control”.
desired microphone sensitivity from 0 % to 99 %. Press ENTER, the display will show “Fans Control”.
1. Tap button, access the main menu, Tap 2. Press , the display will show “Base Control”.
the button until “Personality” is displayed. Press 3. Press , the display will show “Base Control”.
ENTER, the display will show “Personality”. Tap the button until the display will show “Status setting”. will show “10%”, “50%”.
Press ENTER, the display will show “Status setting”. 5. Press to confirm or press to
2. Press , the display will show “Mic Sensitivity”. return to the main menu.
3. Press , the display will show “Mic Sensitivity”.
4. The display show “70%”, Press , the display Display settings
will show “0~99%”. Shut off time
5. Press to confirm or press to With this function you can shut off the color LCD display
return to the main menu. after 2 to 59 minutes. Turn the encoder in order to select the
desired shut off time. The default is 5 minute.
Hibernation - Standby mode
The step motors will be power off if the fixture stay without Display Reverse
DMX signal for 15 mins (Factory default). And the fixture will With this function you can the entire display to be flipped by
be reset before working once it receive DMX signal again. 180˚ to allow for better view when the fixture is hung from
1. Tap button, access the main menu, Tap truss or a ceiling. This function is disabled as default.
the button until Personality” is displayed. Press
12 USER MANUALKey Lock 3. Press , the display will show “Wireless DMX”.
| ENGLISH
With this function you can activate the automatic keylock The display show “Activate WDMX”, Press ,
status. If this function is activated, the keys will be locked the display will show “De-Act WDMX”, “Activate WDMX”, “
automatically after exiting the edit mode for 15 seconds. Act & Data Out”, “Rest WDMX Mem”.
keeping press the [MENU] key for 3seconds if you do not 4. Press to confirm or press to
INSTALLATION INSTRUCTIONS
need this function. return to the main menu.
1. Tap button, access the main menu, Tap
the button until “Personality” is displayed. Restore Default
Press ENTER, the display will show “Personality”. With this function, you can select restore factory set for ON
2. Press , the display will show “Display or OFF, the default is OFF.
Setting”. 1. Tap button, access the main menu, Tap
3. Press , the display will show “Display Setting”. the button until “Personality” is displayed.
4. The display show “Shutoff Time”, Press , Press ENTER, the display will show “Personality”.
the display will show “Display Reverse”, “Key Lock”. 2. Press , the display will show “Restore
5. Press to confirm or press to Default”.
return to the main menu. 3. Press , the display will show “Restore Default”.
4. The display show “OFF”, Press , the display
Temperature C/F will show “ON”.
With this function, Display the temperature for Celsius or 5. Press to confirm or press to
Fahrenheit. return to the main menu.
1. Tap button, access the main menu, Tap
the button until “Personality” is displayed. Reset-functions
Press ENTER, the display will show “Personality”.
2. Press , the display will show “Temperature With this function you can reset the device via the Control
C/F”. Board. You can select the different reset functions by turning
3. Press< ENTER>, the display will show “Temperature the encoder.
C/F”. 1. Tap button, access the main menu, Tap
4. The display show “Fahrenheit”, Press , the the button until “Reset-functions” is displayed.
display will show “Celsius”. Press ENTER, the display will show “Reset-functions”.
5. Press to confirm or press to 2. The display show “Reset All”, Press , the
return to the main menu. display will show “Reset All”, “Reset Pan/Tilt”, “Reset
ZOOM”.
Initial effect 3. Press to confirm or press to
With this function, Display initial effect position. return to the main menu.
1. Tap button, access the main menu, Tap
the button until “Personality” is displayed.
Press ENTER, the display will show “Personality”.
Effect Adjust
2. Press , the display will show “Initial effect”.
3. Press , the display will show “Initial effect”.
Test channel
With this function you can test each channel on its (correct)
4. The display show “XXX”.
function.
5. Press to confirm or press to
1. Tap button, access the main menu, Tap
return to the main menu.
the button until “Effect Adjust” is displayed.
Press ENTER, the display will show “Effect Adjust”.
Wireless DMX
2. Press , the display will show “Test Channel”.
From factory, this Led Moving Head is prepared for wireless
3. Press , the display will show “Test Channel”.
data transmission (W-DMX). If you wish to de-activate W-DMX
4. The display show “Pan Moving” first channel, Press
control, you can select the function “De-activate WDMX” by
, can choose other channel.
turning the encoder. With the function “rest”, you can log out
5. Press to confirm or press to
the Led Moving Head from the wireless sender.
return to the main menu.
1. Tap button, access the main menu, Tap
the button until “Personality” is displayed.
Press ENTER, the display will show “Personality”.
Manual control
With this function, you can control the light sources more
2. Press , the display will show “Wireless
easily. All effects will be canceled, the shutter opens and the
DMX”.
USER MANUAL 13dimmer intensity will be set to 100 %. Edit program
ENGLISH |
1. Tap button, access the main menu, Tap With this function, you can edit the internal programs.
the button until “Effect Adjust” is displayed.
Press ENTER, the display will show “Effect Adjust”. Edit scenes
2. Press , the display will show “Manual With this function, you can edit the scenes of the internal
INSTALLATION INSTRUCTIONS
control”. programs.
3. Press , the display will show “Manual control”.
4. The display show “PAN=XXX”. Rec. Controller
5. Press to confirm or press to The moving head features an integrated DMX-recorder by
return to the main menu. which you can transmit the programmed scenes from your
DMX-controller to the moving head. Adjust the desired
Calibrate values scene numbers via the encoder (from – to). When you call
With this function, you can calibrate and adjust the effect up the scenes at your controller, they will automatically be
wheels to their correct positions. The password of calibrate transmitted to the moving head.
values is 050.
1. Tap button, access the main menu, Tap Excursion
the button until “Effect Adjust” is displayed. A Master unit can send up to 3 different data groups to the
Press ENTER, the display will show “Effect Adjust”. Slave units, i.e. a Master unit can start 3 different Slave units,
2. Press , the display will show “Calibrate which run 3 different programs. The Master unit sends the 3
values”. program parts in a continuous loop.
3. Press , the display will show “Calibrate values”. Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro Auto Pro
Part 1 Part 2 Part 3 Part 1 Part 2 Part 3 Part 1 Part 2 Part 3
4. The display show “Password=XXXX”.
5. Press to confirm or press to The Slave unit receives data from the Master unit according
return to the main menu. to the group which the Slave unit was assigned to. If e.g. a
Slave unit is set to “Slave 1” in the menu “Set to Slave”, the
Users mode set Master unit sends “Auto Program Part 1” to the Slave unit. If
set to “Slave 2”, the Slave unit receives “Auto Program Part
In this menu, user can select different channels list by different 2”.
sequence:
For example, after the user enter this manual, if select Auto To start a Auto Program please proceed as follows:
Program = CH 22, means in this User’s mode, the “Dimmer” 1. Slave-Setting
is in Channel 16. Select “Function Mode” by turning the encoder.
Press the Enter button to confirm.
User mode Select “Set to slave” by turning the encoder.
With this function, you can create user defined channel Press the Enter button to confirm.
orders. Turn the encoder to select “Slave 1”, “Slave 2” or
“Slave 3”.
Preset User mode Press the Enter button to confirm.
With this function, you can adjust the rest user defined Press the MODE/ESC button in order to return to the main
channel order. menu.
1. Tap button, access the main menu, Tap
the button until “Users mode set” is displayed. 2. Automatic Program Run
Press ENTER, the display will show “Users mode set”. Select “Function Mode” by turning the encoder.
2. The display show “User Mode” first channel, Press the display will show “Edit User Mode”. Select “Auto Program” by turning the encoder.
3. Press to confirm or press to Press the Enter button to confirm.
return to the main menu. Turn the encoder to select “Master” or “Alone”. The
selection «Alone» means Stand Alone-mode and «Master»
that the device is defined as master.
Edit program Press the Enter button to confirm.
Press the MODE/ESC button in order to return to the main
Select program
menu.
With this function, you can select the program for the Program
Run.
14 USER MANUAL3. Program selection for Auto Pro Part The 3 Slave groups run the Auto Program in certain time
| ENGLISH
Select “Edit program” by turning the encoder. segments, as shown in the following picture:
Press the Enter button to confirm. Part 1:
Select “Select programs” by turning the encoder. Scene 10 Scene 11 Scene 12 Scene 13
Press the Enter button to confirm.
INSTRUCTIONS INSTRUCTIONS
Turn the encoder to select “Auto Pro Part 1”, “Auto Pro Part 2:
Part 2” or “Auto Pro Part 3”, and thus select which Slave Scene 8S cene 9S cene 10 Scene 8
program is to be sent. Selection “Part 1” means, that the
Slave unit runs the same program as the master units. Part 3:
Press the Enter button to confirm. Scene 12 Scene 13 Scene 14 Scene 15
Press the MODE/ESC button in order to return to the main
menu.
4. Program selection for Edit Program
• Select “Edit program” by turning the encoder.
• Press the Enter button to confirm.
• Select “Edit program” by turning the encoder.
• Press the Enter button to confirm.
• Turn the encoder to select the desired program. With
this function you can edit specific scenes into a specific
program.
• Press the Enter button to confirm.
• Press the MODE/ESC button in order to return to the
main menu.
5. Automatic Scene Recording
Select “Edit program” by turning the encoder.
Press the Enter button to confirm.
Select “Edit scenes” by turning the encoder.
Turn the encoder to select the desired scene numbers.
You can program a maximum number of 250 • Turn the
encoder to select the desired scene numbers. You can
program a maximum number of 250 scenes.
Press the Enter button to confirm.
Press the MODE/ESC button in order to return to the main
menu.
Example:
Program 2 includes scenes: 10, 11, 12, 13
Program 4 includes scenes: 8, 9, 10
Program 6 includes scenes: 12, 13, 14, 15
Auto Pro Part 1 is Program 2
Auto Pro Part 2 is Program 3
Auto Pro Part 3 is Program 6
USER MANUAL 15Instructions on use
ENGLISH |
DMX channel´s functions and their values (44 DMX channels) DMX channel´s functions and their values (44 DMX channels)
Mode/Channel Value Function Mode/Channel Value Function
St Ba Ex St Ba Ex
INSTRUCTIONS ON USE
PAN Movement 8bit Blue LED Fine-array 2
1 1 1 30
0-255 Pan Movement 0-255 Fine control for Blue adjustment
Pan Fine 16bit White LED - array 2
2 2 31
0-255 Fine control of Pan movement 0-255 White ( 0-Black , 255-100% White )
TILT Movement 8bit White LED Fine - array 2
3 2 3 32
0-255 Tilt Movement 0-255 Fine control for White adjustment
Tilt Fine 16bit Red LED - array 3
4 4 33
0-255 Fine control of Tilt movement 0-255 Red ( 0-Black , 255-100% Red )
Speed Pan/Tilt movement Red LED Fine - array 3
34
0-225 max to min speed 0-255 Fine control for Red adjustment
5 3 5
226-235 blackout by movement Green LED - array 3
35
226-235 no function 0-255 Green ( 0-Black , 255-100% Green )
Red LED - all arrays Green LED Fine - array 3
6 4 36
0-255 Red ( 0-Black , 255-100% Red ) 0-255 Fine control for Green adjustment
Red LED Fine - all arrays Blue LED - array 3
7 37
0-255 Fine control for Red adjustment 0-255 Blue ( 0-Black , 255-100% Blue )
Green LED - all arrays Blue LED Fine - array 3
8 5 38
0-255 Green ( 0-Black , 255-100% Green ) 0-255 Fine control for Blue adjustment
Green LED Fine-all arrays White LED - array 3
9 39
0-255 Fine control for Green adjustment 0-255 White ( 0-Black , 255-100% White )
Blue LED - all arrays White LED Fine - array 3
10 6 40
0-255 Blue ( 0-Black , 255-100% Blue ) 0-255 Fine control for White adjustment
Blue LED Fine - all arrays Red LED - array 4
11 41
0-255 Fine control for Blue adjustment 0-255 Red ( 0-Black , 255-100% Red )
White LED - all arrays Red LED Fine - array 4
12 7 42
0-255 White ( 0-Black , 255-100% White ) 0-255 Fine control for Red adjustment
White LED Fine - all arrays Green LED - array 4
13 43
0-255 Fine control for White adjustment 0-255 Green ( 0-Black , 255-100% Green )
Red LED - array 1 Green LED Fine - array 4
17 44
0-255 Red ( 0-Black , 255-100% Red ) 0-255 Fine control for Green adjustment
Red LED Fine - array 1 Blue LED - array 4
18 45
0-255 Fine control for Red adjustment 0-255 Blue ( 0-Black , 255-100% Blue )
Green LED - array 1 Blue LED Fine - array 4
19 46
0-255 Green ( 0-Black , 255-100% Green ) 0-255 Fine control for Blue adjustment
Green LED Fine-array 1 White LED - array 4
20 47
0-255 Fine control for Green adjustment 0-255 White (0-Black , 255-100% White )
Blue LED -array 1 White LED Fine -array 4
21 48
0-255 Blue ( 0-Black , 255-100% Blue ) 0-255 Fine control for White adjustment
Blue LED Fine-array 1 Shutter, strobe
22
0-255 Fine control for Blue adjustment 0-31 Led turn off
White LED -array 1 32-63 Led turn on
23
0-255 White ( 0-Black , 255-100% White ) 64-95 Strobe effect slow to fast
White LED Fine - array 1 14 8 6 96-127 Led turn on
24
0-255 Fine control for White adjustment 128-159 Pulse-effect in sequences
Red LED - array 2 160-191 Led turn on
25
0-255 Red ( 0-Black , 255-100% Red ) 192-223 Random strobe effect slow to fast
Red LED Fine - array 2 224-255 Led turn on
26
0-255 Fine control for Red adjustment Dimmer intensity
15 9 7
Green LED - array 2 0-255 Intensity 0 to 100%
27
0-255 Green ( 0-Black , 255-100% Green ) Dimmer intensity Fine
16 8
Green LED Fine - array 2 0-255 Fine control for Dimmer adjustment
28
0-255 Fine control for Green adjustment
Blue LED - array 2
29
0-255 Blue ( 0-Black , 255-100% Blue )
16 USER MANUAL| ENGLISH
DMX channel´s functions and their values (44 DMX channels) DMX channel´s functions and their values (44 DMX channels)
Mode/Channel Value Function Mode/Channel Value Function
St Ba Ex St Ba Ex
INSTRUCTIONS ON USE
Color Macro Chase Patterns
0-7 No function 1--14 Led turn off
8-39 from RED to YELLOW 15-30 Chase 1
40-71 from YELLOW to GREEN 31-46 Chase 2
72-103 from GREEN to CYAN 47-62 Chase 3
17 10 9
104-135 from CYAN to BLUE 63-78 Chase 4
136-167 from BLUE to MAGENTA 79-94 Chase 5
168-199 from MAGENTA to RED 95-110 Chase 6
200-231 from RED to WHITE 20 13 12 111-126 Chase 7
232-255 Crossfading colours from slow to fast 127-142 Chase 8
Color Presets 143-158 Chase 9
0-4 No function 159-174 Chase 10
5--9 White2700k 175-190 Chase 11
10--14 White3200k 191-206 Chase 12
15-19 White4300k 207-222 Chase 13
20-24 White5600k 223-238 Chase 14
25-29 White6500k 239-255 Chase 15
30-34 White8000k Chase Speed
35-39 Red 0-125 Fast to Slow Backward
21 14 13
40-44 Green 126-130 Stop(Speed=0)
45-49 Blue 131-255 Slow to Fast Forward
50-54 Natural White Chase Fade
22 15 14
55-59 Full White 0-255 Fade Chase
60-64 Yellow Zoom
23 16 15
65-69 Magenta 0-255 Zoom adjustment from 11° to 45°
18 11 10 70-74 Cyan Zoom Fine
16
75-79 Salmon 0-255 Fine control for Zoom adjustment
80-84 Turquoise Lamp on/off, reset, internal programs
85-89 Light Green 0-79 Normal
90-94 Steel Blue 80-84 All motor reset
95-99 Orange 85-87 Zoom motor reset
100-104 Straw 88-90 no function
105-109 Pale Lavander 91-93 no function
110-114 Pink 94-96 no function
115-119 RED/WHITE 97-99 Others motor reset
24 17 49
120-124 GREEN/RED 100-119 Internal program 1 (scene 1~8 of EEPROM)
125-129 BLUE/RED 120-139 Internal program 2 (scene 9~16 of EEPROM)
130-134 WHITE/RED 140-159 Internal program 3 (scene 17~24 of EEPROM)
135-139 WHITE/PINK 160-179 Internal program 4 (scene 25~32 of EEPROM)
140-144 WHITE/TURQUOISE 180-199 Internal program 5 (scene 33~40 of EEPROM)
145-149 SMALL RED/WHITE 200-219 Internal program 6 (scene 41~48 of EEPROM)
150-255 Reserved 220-239 Internal program 7 (scene 49~56 of EEPROM)
Color Presets Dimmer 240-255 Music Control (scene of Program 1)
19 12 11
0-255 Dimmer 100 to 0% Remark: The color of Chase Patterns is according to the RGBW four
channel and Color presets channel, if these channel are unactived, the
Chase Patterns would come out no effect.
USER MANUAL 17Error message
ENGLISH |
CAUTION !
When you turn on the fixture, it will make a reset at first. Disconnect from mains before
The display may show “Err channel is XX” while there are starting maintenance operation
ERROR MESSAGE | CLEANING AND MAINTENANCE | TECHNICAL SPECIFICATIONS
problems with one or more channels. “XX” stands for channel
1, 2, 3, 4, 5, 6 who has the testing sensor for positioning. We recommend a frequent cleaning of the device. Please
For example, when the display shows “Err channel is Pan use a moist, lint- free cloth. Never use alcohol or solvents.
movement”, it means there is some error in channel 1. If there There are no serviceable parts inside the device. Please refer
are some errors on channel 1, channel 3, channel 23 at the to the instructions under “Installation instructions”.
same time, you may see the error message “Err channel is Should you need any spare parts, please order genuine parts
Pan movement”, “Err channel is Tilt movement”, “Err channel from your local dealer.
is Zoom” flash repeated for 2 times, and then the fixture will
generate a second reset. If the fixture remain error message
after performing reset more than 2 times, only the channels Technical specifications
which have errors can not work properly, others can work as
usual. Please contact with dealer or manufacturer for service,
Optics
self repair is not allowed.
4:1 zoom optics system
75% optic efficiency
PAN - movement Er Beam aperture: from 11° to 45°
(PAN-head movement error) This message will appear Motorised linear zoom
after the reset of the fixture if the head’s magnetic-indexing
circuit malfunctions (sensor failed or magnet missing) or the
Source
stepping-motor is defective (or its driving IC on the main PCB).
31 Multi-chip High-Power LEDs sources
The TILT- movement is not located in the default position after
Light output: up to 10.000 lumen
the reset.
Rated Sources life: 25.000 hours
Flicker free sources Management, convenient for TV
TILT- movement Er applications and all video recorded events
(TILT-head movement error) This message will appear after
the reset of the fixture if the head’s magnetic-indexing
Movement
circuit malfunctions (sensor failed or magnet missing) or the
Extremely accurate positioning
stepping-motor is defective (or its driving IC on the main PCB).
Moving-head operated via either
The TILT- movement is not located in the default position after
or 8/16 bit resolution
the reset.
High-resolution stepper motors operated via microprocessors
ensure extreme accuracy and smooth movements
PAN and TILT automatic repositioning
Cleaning and maintenance Moving head range: 540° (PAN), 270° (TILT)
The following points have to be considered during the Colours
inspection: Sophisticated 4 colours RGB+W mixed, reaching high Colour
All screws for installing the devices or parts of the device Rendering Index
have to be tightly connected and must not be corroded. Uniform light beam with no colour shadows, and rich
There must not be any deformations on the housing, saturated colour-hues
color lenses, fixations and installation spots (ceiling, 8 or 16 bit resolution
suspension, trussing). 4,29 billion colours (8 bit resolution)
Mechanically moved parts must not show any traces of Virtual colour wheel including White presets
wearing and must not rotate with Pre-programmed colours and rainbow effect
unbalances.
The electric power supply cables must not show any Dimmer, strobe
damage, material fatigue or sediments. Electronic dimmer for adjustment of light output from 0 to
Further instructions depending on the installation spot and 100% with no colour variation (16 bit)
usage have to be adhered by a skilled installer and any High-speed white or full colour strobe effect with variable
safety problems have to be removed. 1-25 fps flash rate
Pre-programmed variable strobe effect
18 USER MANUALControl standard connection systems
| ENGLISH
512 USITT, with built-in Wireless DMX receiver Mounting points: Four ¼ turn locking fittings, allowing 4
Master / Slave functionalities to manage different installation of ¼ turn brackets
several projectors without DMX lighting Desk Safety cable attachment point
TECHNICAL SPECIFICATIONS
17 / 24 / 49 DMX channels required to control all parameters
of the projector Operating parameters
Selectable DMX Modes Working position: Any
Maximum ambient temperature (Ta): 45°C
Software facilities
Fixture settings for DMX address and functions Conformity
DMX-RDM Ready EU (EMC) : EN 50081-1, EN 50082-1
On/off LCD display EU (Electrical Safety) : EN 60598-1,
8/16 bit movement resolution selection EN 60598-2-17
Pan & tilt inversion facility
Sophisticated control of cooling parameters to reduce noise Size
Selectable Ventilation User’s Modes 446 x 544 x 305 mm (l x h x d)
Pre-set sequence control
Software upgrade via DMX
Weight
22,8 Kg
Hardware facilities
Graphic LCD display for addressing and special functions 107
setting read out with flip function
5 menu buttons for setting the functions
Over temperature protection
Control by DMX 512 standard signal
via 3 pin & 5 pin XLR or Wireless DMX
107
93
Pan and Tilt Lock system to ease-up
transportation
Power supply 446 200
Any AC Voltage power supply between 110 to 240 Volts n 330
(50/60 Hz)
Electronic Power Supply with active PFC (Power Factor
Correction)
544
Cooling system
379
Advanced ventilation cooling system
Self adjusting variable speed fans for quiet operation (Fan
125
Auto Mode)
371 305
Selectable Ventilation User’s Modes
Housing
Construction: Self-extinguishing V0 class fire-retardant
ABS PC moulded covers. Moving head skeleton made of
Aluminium and Steel metal plates
Two sides handles for transportation
IP20 protection rating
Exterior finish: Carbon (Black)
Rigging
Fastening Brackets System: Two Omega
¼ turn brackets designed for use with
USER MANUAL 19Vous pouvez aussi lire
